My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
6(a) American Flag Illumination - Discussion
Laserfiche
>
Planning & Zoning
>
Agenda Packets
>
2019
>
11-21-2019 Planning & Zoning Commission Meeting
>
6(a) American Flag Illumination - Discussion
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
11/14/2019 3:11:06 PM
Creation date
11/14/2019 3:11:05 PM
Metadata
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
10
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
View images
View plain text
(C) Dawn to Dusk Luminance Standards <br /> (i) All sign and decorative light sources must not exceed 6,500 nits. <br /> 6) Flagpoles. A flagpole may be illuminated by no more than three upward aimed fully shielded <br /> spotlight light fixtures per flag. For flag poles up to 35 feet in height, the fixtures must not exceed a <br /> combined 40,000 initial light output lumens for flags of 35 feet or less in height. An additional 500 <br /> initial light output lumens for each foot in flag height, not pole height, over 35 feet is allowed up to a <br /> maximum of 75,000 initial light output lumens. The light fixtures must be placed as close to the <br /> base of the flagpole as reasonably possible and recessed into the ground. <br /> (7) Canopy lighting. Light fixtures mounted under roof overhangs and canopies must be recessed so <br /> that the lens cover is recessed or flush with the bottom surface (soffit)of the canopy and/or <br /> shielded by the fixture or the edge of the canopy so that light is restrained to no more than 85 <br /> degrees from vertical. Lights must not be mounted on the top or sides(fascia) of the canopy for <br /> the purposes of illuminating a portion or the entire canopy. <br /> (A) Example of complying recessed canopy light: <br /> Canopy Lighting <br /> Car�op�r <br /> Fa�cl� <br /> R�o�ss�d <br /> �1xMx� <br /> '� 6' <br /> � -- <br /> � ' <br /> L�ns � � <br /> � <br /> � �< <br /> (8) Building entrances or exits. A light source must be located at each building entrance and exit. <br /> (9) Glare. In all zoning districts, all lighting must be arranged so as not to shine directly on any <br /> adjoining property. A person must not create light that produces glare clearly visible beyond a <br /> property line or creates a sensation of brightness within a visual field so as to cause annoyance, <br /> discomfort or impairment of vision. Lenses, deflectors, shields, louvers, or prismatic control <br /> devices must be used to eliminate nuisance and hazardous lighting to facilitate compliance with <br /> this requirement. <br /> (10) Parking structures. Luminaires used for illumination of designated pedestrian walkways in <br /> parking structures must be at least finro times the average illumination or of a significantly different <br /> color value than luminaires used for illuminating vehicle parking and drive aisles. Convex lenses in <br /> open parking garages must not extend more than two inches below the source. Fully enclosed <br /> and secured parking structures are exempt from the cut-off and lens restrictions. <br /> (11) Proof of lighting. A parking lot used exclusively for daylight use and secured to prohibit nighttime <br /> use is exempt from the lighting requirements subject to installation of all conduit and material, other <br /> than the lighting and lighting supports, subject to approval by the Issuing Authority. <br /> (12) Lighting standards. All exterior lighting must comply with the following standards, which vary by <br /> use. In the event more than one use is present, the highest regulatory standards apply. Single- <br /> family and two-family dwellings and residential parking lots with fewer than finrelve parking spaces <br /> are exempt from the minimum light levels required but shall comply with the lights source and <br /> height requirements for any lighting installed. Maintained lighting levels shall be calculated at a <br /> Light Loss Factor of 0.81 or the actual tested Light Loss Factor for the source, whichever is less. <br />
The URL can be used to link to this page
Your browser does not support the video tag.